Enviro ascot manual

Massachusetts installations Warning : This product must be installed by a licensed plumber or. Other Massachusetts code.

A carbon. The fireplace. This appliance may be installed in an. Table of Contents. Previous Page. Next Page. Enviro - sherwood industries ltd. Carefully read all the instructions in this manual first. Consult the building authority having jurisdiction to determine the need for a permit prior to commencing the installation.

Page 4: Codes And Approvals After the unit has gone through the first burn, turn the unit off including the pilot, let the unit get cold then remove the glass door and clean it with a good gas fireplace glass cleaner, available at your local ENVIRO dealer. Do not touch. Keep children, clothing, furnit ure, gasoline or other flammable vapors away. Replacement of this glass should be done by a licensed or qualified person! This appliance needs fresh air for safe operation and must be installed with provisio ns for combustion and ventilation air.

Turn off the gas to the fireplace. If not recently done, remove the glass and let the unit air out for at least five 5 minutes to clear out any gas. Turn on gas to the heater.

Leak test all joints with soapy water. Page 9: Replacing Glass Do not operate with the glass front removed, cracked or broken. Removal and replacement of the glass from the door must be done by a licensed or qualified service person. No substitute materials are allowed. If damage is found, please report it to both the carrier and your dealer as soon as possible. It is important to note when passing through a wall, the maximum allowable wall thickness is 10 inches Vent Termination Restrictions, refer to Table 2.

Failure to follow these instructions carefully could cause property damage or personal injury. Use of these systems with the Direct Vent GS starting collar is deemed acceptable and does not affect the Intertek WH listing of the appliance.

There is a small rectangular hole in the air jacket. Slide the hex bolt to the next setting and retighten the bolt to ensure the plate does not move Figure Other Massachusetts. Previous Page. Next Page. Enviro Ascot Owner's Manual 40 pages. Enviro Ascot Owner's Manual 33 pages. Enviro - sherwood industries ltd. Set the appliance in the desired location. Check to determine if wall studs are in the way when the venting system is attached. If this is the case, you may want to adjust the location of the appliance.

STEP 2. If the information in these instructions is not followed exactly, a fire, explosion or CO poisoning may result. This model has a millivolt gas control, which uses the pilot flame to generate enough electricity to operate the main burners. The appliance when equipped with an optional blower must be electrically connected and grounded in accordance with local codes or in the absence of local codes, with the current CSA C Page 4: Codes And Approvals After the unit has gone through the first burn, turn the unit off including the pilot, let the unit get cold then remove the glass door and clean it with a good gas fireplace glass cleaner, available at your local ENVIRO dealer.

Dimensions of the Ascot. Do not touch. Keep children, clothing, furnit ure, gasoline or other flammable vapors away. Replacement of this glass should be done by a licensed or qualified person! This appliance needs fresh air for safe operation and must be installed with provisio ns for combustion and ventilation air.

Burner Light pop or poof when turned off; this is more common with LP units. Temperature Sensor Clinking when it senses to turn the blower on or off. Page 8: Maintenance And Service. Check the gasket material on the back of the glass, making sure that it section. SIT Valve on Ascot. Page 9: Replacing Glass Do not operate with the glass front removed, cracked or broken.

Removal and replacement of the glass from the door must be done by a licensed or qualified service person. No substitute materials are allowed. If damage is found, please report it to both the carrier and your dealer as soon as possible. It is important to note when passing through a wall, the maximum allowable wall thickness is 10 inches Vent Termination Restrictions, refer to Table 2. Failure to follow these instructions carefully could cause property damage or personal injury.

Use of these systems with the Direct Vent GS starting collar is deemed acceptable and does not affect the Intertek WH listing of the appliance. There is a small rectangular hole in the air jacket.

Slide the hex bolt to the next setting and retighten the bolt to ensure the plate does not move Figure Set the appliance in the desired location. Check to determine if wall studs or roof rafters are in the way when the venting system is attached.

If this is the case, you may want to adjust the location of the appliance. The center of the square hole should match the center line of the horizontal pipe. Check the instructions for required clearances air spaces to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces.

Do not pack air spaces with insulation. Set the gas appliance in the desired location. Drop a plumb bob down from the ceiling to the position of the appliance flue exit, and mark the location where the vent will penetrate the ceiling.

Tighten the clamp around the pipe section.